Fs ⁄ Fc
MMSx Authority · Applied Biomechanics Education Series
★ Module 02 of 05 Dr. Neeraj Mehta, PhD ● ORCID 0000-0001-6200-8495 Spinal Load Direction

Shear vs Compression
The Missing Language of Spinal Load Management

Why the Direction of Spinal Load Matters More Than Its Magnitude

Two lifters generate identical peak spinal force. One goes home sore; the other goes home injured. The difference is rarely the magnitude of the load — it is its direction. Shear and compression are mechanically, histologically, and clinically different phenomena, yet most load-management decisions treat “spinal stress” as a single undifferentiated variable. This module restores the language the field has lost.

● Shear force Fs · Compressive force Fc · NIOSH 3 400 N limit ● NCT07220200 · NCT07296640 · NCT07256717 ● EIN 41-2717794 · 501(c)(3) Nonprofit
Module Title
Shear vs Compression
The Missing Language of Spinal Load Management
Series
Applied Biomechanics Education Series
MMSx Authority Institute
Author / Lead Academic
Dr. Neeraj Mehta, PhD
ORCID 0000-0001-6200-8495
Institutional Affiliation
MMSx Authority Institute
EIN 41-2717794 · Powell, Ohio, USA
Academic Level
MSc / PhD Seminar / CPD
Advanced undergraduate permitted with tutor support
Study / Seminar / Assessment
60 min · 60 min · 45–75 min
Total learning time: approximately 3 hours
Version
1.0
Published 18 April 2026
Reviewer Status
Institutional Review ✓
MMSx Scientific Review Board
Contact
Faculty adoption enquiries welcome
Fs / Fc
Two forces, one spine, different tissues
1 000 N
Approx. cumulative shear tolerance of the lumbar motion segment
3 400 N
NIOSH lifting action-limit for lumbar compression
>3×
Tissue tolerance asymmetry: compression / shear
6
Sections · Mechanism through Clinical Translation
LO

Learning Outcomes

Upon completion of this module, the learner will be able to execute the following academic and clinical operations. These outcomes are the examinable foundation of the module and map directly to the assessment layer below.

By the end of this module, the learner will be able to —
  • Explain the mechanical distinction between shear (Fs) and compressive (Fc) loading of the spine, and the anatomical structures that resist each.
  • Apply published tissue-tolerance values to estimate when a task exceeds safe shear or compressive thresholds at the L4–L5 motion segment.
  • Compare two mechanically similar tasks that differ primarily in shear-to-compression ratio, and predict their differential clinical risk profiles.
  • Interpret a coaching or rehabilitation recommendation through the shear-vs-compression lens, identifying whether the recommendation manages direction or merely magnitude.
  • Evaluate whether a published exercise guideline or occupational handling protocol adequately distinguishes shear exposure from compressive exposure, and identify specific improvements.
  • Critique the common clinical shorthand of “spinal load” as a single undifferentiated variable, grounded in histology, biomechanical modelling, and tissue-tolerance evidence.
CP

Curriculum Positioning

This module is designed for postgraduate and CPD-level delivery within biomechanics, sports and exercise science, musculoskeletal physiotherapy, ergonomics, strength and conditioning, and clinical exercise science curricula. It builds directly upon the mechanical-decision framing established in Module 01 (Torque Before Technique) and is prerequisite for Module 03 (Neutral Spine Is Not a Position).

Target Audience
MSc / PhD biomechanics · physiotherapy · ergonomics · S&C
Academic Level
Level 7 – 8 (FHEQ); AQF 9; UK Masters / Doctoral seminar
Reading Duration
60 min independent study
Seminar Duration
60 min facilitated seminar or clinical tutorial
Assessment Duration
45–75 min total (MCQ + short-answer + case task)
Prerequisites
Introductory biomechanics; Module 01 (Torque Before Technique) recommended
Prescribed Role In Curriculum
Foundational spinal-load module — precedes Module 03 (Neutral Spine)
Delivery Modes
Self-study, flipped classroom, clinical CPD, LMS package
01

The Mechanical Distinction That the Clinic Rarely Names

Spinal loading is not one phenomenon. It is the vector sum of at least two mechanically distinct force components acting on every motion segment: compressive force (Fc), which acts axially along the longitudinal axis of the spine and presses adjacent vertebrae together; and shear force (Fs), which acts transverse to that axis and translates one vertebra across its neighbour. These forces are resisted by different anatomical structures, they fail through different histological mechanisms, and they tolerate radically different magnitudes before tissue injury occurs.

The clinical and coaching literature often collapses these two forces into a single “spinal load” variable. That compression of language is a technical error with consequences. A task producing 3 000 N of axial compression with minimal shear is a very different mechanical event from a task producing 1 200 N of shear with modest compression — even though both might be colloquially described as “stressful to the back.” The first is within the NIOSH lifting action-limit for compression [1]; the second exceeds published shear-tolerance thresholds for the lumbar motion segment [2,3] and may cause injury with far fewer exposures.

```
Ftotal = √(Fc² + Fs²)
Fc = Compressive component — axial, along the spinal long axis (N)
Fs = Shear component — transverse, perpendicular to the axis (N)
Ftotal = Resultant vector magnitude; directionally agnostic — and therefore clinically insufficient on its own
Figure 1
Compression and Shear at a Lumbar Motion Segment
Figure 1. Compression and shear vectors at a lumbar motion segment A simplified schematic shows two adjacent lumbar vertebrae separated by an intervertebral disc. A downward vertical arrow labelled F-c represents compressive force along the long axis of the spine, acting on the disc and endplates. A horizontal arrow labelled F-s represents shear force acting transverse to the long axis, translating the upper vertebra anteriorly relative to the lower. The diagram illustrates that the two force components act on different anatomical restraints: compression on the disc and endplates, shear on the facet joints and posterior ligamentous complex. Upper vertebra (L4) Intervertebral disc Lower vertebra (L5) Fc axial compression Fs transverse shear facet joints resist shear disc & endplates resist compression spinal long axis
Figure 1. Two force components act on every lumbar motion segment. Compressive force (Fc, red, vertical) loads the intervertebral disc and vertebral endplates along the spinal long axis. Shear force (Fs, purple, horizontal) translates adjacent vertebrae and is resisted primarily by the facet joints, the neural arch, and the posterior ligamentous complex. These are different anatomical restraints, with different failure modes and different tolerance values.
Fc
Compressive force — axial, resisted by disc and endplates
Fs
Shear force — transverse, resisted by facets and ligaments
>3×
Tissue tolerance asymmetry between compression and shear
↔
Magnitude-only thinking hides the most injurious component
```
02

Why the Spine Tolerates Compression Far Better Than Shear

Tissue tolerance is not a universal number; it is a property of the specific structure loaded and the specific direction in which it is loaded. The lumbar intervertebral disc, the vertebral endplate, and the cancellous bone of the vertebral body are architecturally optimised for axial compression — they distribute compressive pressure across a large horizontal cross-section and dissipate it through fluid pressurisation and trabecular buckling. These structures are not architecturally optimised for horizontal translation.

Shear at the lumbar motion segment is resisted by the facet joints, the neural arch, the pars interarticularis, and the posterior ligamentous complex. These structures are smaller, more focal, and more vulnerable to repeated horizontal displacement. Cyclic shear loading, even at moderate magnitudes, has been associated with pars defects, facet capsule injury, and spondylolisthetic progression [2,3]. Consequently, the published tolerance values for shear are substantially lower than those for compression.

```
Load component & structure
Single-cycle threshold (approx.)
Cumulative / fatigue threshold
Source
Compression · disc + endplates
~6 400 N (endplate fracture in vitro)
NIOSH action-limit 3 400 N; upper limit 6 400 N
NIOSH 1981 [1]; McGill 2015 [4]
Shear · facets + posterior elements
~2 000–2 800 N (in vitro single cycle)
Cyclic tolerance ~1 000 N; lower with repeated exposure
Yingling & McGill 1999 [2]; McGill 1997 [3]
Combined · compression + shear
Lower than either alone at equivalent magnitudes
Interactive — shear reduces compressive tolerance
Gallagher & Marras 2012 [5]

The operational conclusion is unambiguous. Given the same magnitude of force, shear is the more clinically injurious direction. A task that delivers 2 500 N as pure compression sits comfortably below the disc’s acute tolerance. The identical 2 500 N delivered as shear is within an order of magnitude of the single-cycle failure threshold for the posterior elements, and above the cumulative shear tolerance identified in fatigue-loading studies. The same number — applied in a different direction — describes two categorically different mechanical events.

⚠ Clinical Implication
When screening a task, protocol, or coaching recommendation, the shear component must be estimated separately from the compressive component. A total force within NIOSH compression limits can still exceed shear tolerance if the task geometry generates substantial horizontal translation at the loaded segment. Total-force estimation is not a shear screen.
```
03

Two Tasks, Identical Peak Force, Different Injuries

Consider two common gym and occupational tasks. Both generate a peak lumbar resultant force of approximately 3 200 N at L4–L5. Both are widely described as “heavy on the back.” In magnitude-only reasoning, they are equivalent. In shear-vs-compression reasoning, they are not.

```
Variable
⚠ Forward-lean barbell row
✓ Upright barbell squat
Total resultant force at L4–L5
~3 200 N
~3 200 N
Estimated compressive component Fc
~2 400 N
~3 100 N
Estimated shear component Fs
~2 100 N (high)
~780 N (low)
Relation to shear tolerance (~1 000 N cyclic)
>2× above cyclic tolerance
Below cyclic tolerance
Relation to compression tolerance (NIOSH 3 400 N)
Below action-limit
Below action-limit
Dominant clinical concern
Posterior-element injury; spondylolisthetic progression
Endplate / disc load; within tolerance envelope
MMSx Authority · Spinal Load Direction Principle “The most injurious spinal task in a training programme is rarely the one with the highest number on the bar. It is the one with the highest shear-to-compression ratio that the practitioner failed to measure.”
🔬 Why This Is Missed
The forward-lean barbell row can be performed with a lighter absolute load than the squat and still generate markedly higher shear. Because the absolute weight on the bar is lower, the task is typically categorised as “an accessory exercise” rather than “a heavy lift.” This framing is mechanically inverted: the accessory exercise may be producing the more dangerous force component. Direction-aware load management corrects this inversion.
```
04

A Shear-Aware Decision Framework

Direction-aware spinal-load management reorganises how tasks are selected, sequenced, and progressed. The four decision principles below operationalise the shear-vs-compression distinction into load-management practice. They are not novel inventions — they are explicit statements of what competent biomechanical reasoning has always implied but rarely said aloud.

```
Decision principle
⚠ Magnitude-only thinking
✓ Direction-aware thinking
Task categorisation
Classified by load on the bar
Classified by shear-to-compression ratio at the limiting segment
Exposure budgeting
Total tonnage per week
Separate cumulative budgets for Fc and Fs exposure
Progression
Linear load progression on every task
Shear-dominant tasks progress conservatively; compression-dominant tasks progress more aggressively
Red-flag detection
Absolute load or perceived exertion
Trunk-angle deviation that shifts compression into shear
✓ MMSx Framework Alignment
The BPIT™ 5-Line Principle (DOI 10.5281/zenodo.17594977; NCT07296640) operationalises direction-aware progression within the integrated training framework. In the BPIT progression logic, shear-dominant movement patterns do not advance in load on the same schedule as compression-dominant patterns — a direct translation of the tolerance asymmetry described above. The MMSx-SCAN™ v2.1 assessment (DOI 10.17605/OSF.IO/F87N2) includes a shear-posture sub-screen that flags trunk-angle behaviours indicative of shear drift during loading.
```
05

Applied Clinical Case: The Occupational Loader with “Back Stiffness”

The following case is structured for seminar discussion. It illustrates how a task whose total magnitude is within acceptable limits can still exceed the tolerance envelope when shear is separated from compression. The purpose is to train the learner to audit spinal load as two independent components, not one aggregate number.

```
Case A · Worker M
42-year-old warehouse loader, 78 kg, repetitive box lift and carry

Worker M performs approximately 180 lift-and-place cycles per shift. Each lift involves a ~14 kg box, retrieved from an ankle-height shelf and placed on a waist-height conveyor. Ergonomic audit estimates peak L4–L5 compressive force at approximately 3 100 N and peak shear force at approximately 1 400 N, with the shear peak occurring during the early portion of the lift when trunk flexion is maximal.

The worker reports daily lumbar stiffness and occasional unilateral low back discomfort. Imaging is unremarkable. The occupational-health protocol flags the task as “within NIOSH compression action-limit” and recommends no modification. Symptoms persist.

» Discussion prompt: Apply the shear-vs-compression framework. Is this task within tolerance? If not, which component exceeds which threshold — and what is the single highest-yield modification to reduce shear without changing the compressive load? Reference the tolerance values in Section 2.
Case B · Worker N
44-year-old warehouse loader, 80 kg, same task re-engineered

Worker N performs the same 180 cycles per shift with the same 14 kg box. After ergonomic redesign — the lowest shelf was raised to knee height and a hip-hinge lifting cue was reinforced — estimated peak L4–L5 compressive force is approximately 2 900 N (a modest reduction), but peak shear has dropped to approximately 650 N (a substantial reduction). The worker reports resolution of daily stiffness within four weeks of the redesign.

» Discussion prompt: The total resultant force at L4–L5 barely changed between Worker M and Worker N — yet clinical symptoms resolved. Explain this outcome using the tolerance asymmetry established in Section 2, and discuss why a “total load” metric would have missed the clinically relevant variable.
MMSx Core Teaching
“The spine does not feel force. It feels direction. The clinician who audits only magnitude audits only half the problem.”
— Dr. Neeraj Mehta, PhD · MMSx Authority Institute · ORCID 0000-0001-6200-8495
```
AL

Assessment Layer

The assessment below maps directly to the learning outcomes declared at the opening of the module. It includes five multiple-choice questions, two short-answer questions, one case-based discussion prompt for seminar use, and one applied biomechanics interpretation task for formal grading.

```
Multiple-Choice Questions (5)
Test: recall + application
Q1Compressive force at a lumbar motion segment is primarily resisted by which structures?
  • The facet joints and posterior ligamentous complex.
  • The intervertebral disc and vertebral endplates.
  • The erector spinae and multifidus musculature.
  • The thoracolumbar fascia alone.
Answer: B. Axial compression is distributed across the horizontal cross-section of the disc and transferred through the vertebral endplates into cancellous bone. The facets and posterior elements are the primary shear restraints, not compression restraints.
Q2The NIOSH lifting action-limit of approximately 3 400 N refers specifically to which load component at L5–S1?
  • Shear force Fs.
  • Compressive force Fc.
  • Total resultant force Ftotal.
  • Muscular tensile force.
Answer: B. The NIOSH action-limit is a compression threshold. It does not set a shear limit, which is why direction-aware audits must estimate shear separately.
Q3A task produces 2 500 N at L4–L5. Which scenario carries the greater clinical risk of posterior-element injury?
  • 2 500 N delivered as pure axial compression.
  • 2 500 N delivered as shear with minimal compression.
  • Both scenarios carry identical risk because the magnitude is the same.
  • The risk depends solely on repetitions.
Answer: B. 2 500 N of shear approaches the single-cycle failure threshold for the posterior elements and substantially exceeds cyclic shear tolerance. 2 500 N of axial compression is well below the NIOSH action-limit.
Q4In the worked comparison between a forward-lean barbell row and an upright barbell squat at equal total lumbar force, the row carries greater injury risk primarily because:
  • The row is performed with a heavier absolute load.
  • The row produces a higher shear-to-compression ratio, loading the lower-tolerance direction more heavily.
  • The row involves greater muscular fatigue.
  • The row is performed more frequently.
Answer: B. Equal total force is irrelevant when the ratio of shear to compression differs. The row drives a larger proportion of the total into shear, which has a lower tolerance threshold.
Q5Which of the following is the most mechanically accurate description of “spinal load” in a clinical or coaching report?
  • A single scalar value representing the total force at the segment.
  • A vector description specifying compressive and shear components separately, with reference to the structures that resist each.
  • The weight on the bar divided by body mass.
  • The athlete’s rating of perceived exertion.
Answer: B. Spinal load is a vector quantity. Reporting only the magnitude hides the clinically relevant direction.
Short-Answer Questions (2)
Test: written articulation
Short Answer · Q6
In 150–250 words, explain why the lumbar motion segment tolerates substantially higher compressive force than shear force. Your answer should reference at least two specific anatomical structures and the published tolerance values given in Section 2.
Marking guide: correct identification of compression-resisting structures (25%); correct identification of shear-resisting structures (25%); correct tolerance values with units (25%); mechanical explanation of the tolerance asymmetry (25%).
Short Answer · Q7
In 150–200 words, describe why a training or rehabilitation programme that tracks only total tonnage per week can underestimate true spinal-injury risk. Propose one specific modification to a weekly programming sheet that would make shear exposure visible to the coach.
Marking guide: explanation of why total tonnage hides shear (40%); realism of the proposed programming modification (30%); mechanical defensibility of the modification (30%).
Case-Based Discussion Prompt
Seminar use · 45 min facilitated
Seminar Case
The Competitive Deadlifter with Recurring Lumbar “Niggle”

A 29-year-old competitive deadlifter (82 kg, pulls 260 kg conventional) has been flagged by her coach because of recurring unilateral lumbar discomfort appearing in the final 48 hours of each training block. The discomfort resolves with one deload week and reappears in the next block. Video shows a consistent ~12 degrees of lateral trunk shift during the concentric phase of her top-set singles, but little shift during back-off sets. Imaging is unremarkable. Total lumbar force at L4–L5 on top singles is estimated at 4 900 N; on back-off sets at 3 600 N.

In small groups (4–6 participants), apply the shear-vs-compression framework to this case. Estimate the shear component on top singles versus back-off sets given the lateral shift. Propose a direction-aware load-management modification that preserves training stimulus. Identify why a magnitude-only audit would have prescribed only a deload.

» Deliverable: a 5-slide group presentation that quantifies the estimated shear differential, proposes a shear-aware programming modification, and demonstrates why magnitude-only reasoning is insufficient.
Applied Biomechanics Interpretation Task
For formal grading · 1–2 pages
Applied Task · Graded
Audit a Published Spinal-Load Guideline

Select one publicly available spinal-load guideline — an occupational lifting standard, a clinical rehabilitation protocol, a professional body position statement, or a widely cited strength-training recommendation. Do not select one authored by MMSx Authority.

Produce a 1–2 page written analysis that (i) summarises the guideline, (ii) identifies whether it treats spinal load as a single aggregate variable or as separate compressive and shear components, (iii) quantifies — with at least one worked example — a task where the guideline would classify exposure as safe while a direction-aware audit would flag it, and (iv) proposes a direction-aware revision.

» Marking rubric: identification of magnitude-only reasoning in the guideline (25%); quality of the worked example with numerical estimates (30%); defensibility of the revision (30%); correct use of at least three references from the module list (15%).
Note on assessment and credentials. Successful completion of the module assessment (5 MCQs, 2 short-answer questions, and the applied interpretation task) may support issuance of a Module Completion Certificate or digital badge in Shear vs Compression. Broader Micro-Certificates require completion of multiple modules within the Applied Biomechanics Education Series together with cumulative assessment. See the Credential Pathway section immediately below for the full ladder.
```
CP

Assessment Outcome & Credential Pathway

```
What completion of this module signifies
Successful completion of this module’s assessment indicates that the learner can explain, apply, and defend the shear-vs-compression framework at postgraduate level — specifically, the principle that spinal load must be audited as two directional components, with separate tissue-tolerance envelopes, before any load-management, coaching, or rehabilitation decision is made. It does not, by itself, constitute a professional certification, licensure, or accreditation. The credential structure below reflects this distinction clearly, so that learners, institutions, and faculty adopters understand precisely what a module-level result does and does not confer.
Level 1 · Module Completion
Module Completion Certificate or Digital Badge
Single-Module Assessment
Learners who successfully complete the assessment for this module may be eligible for a Module Completion Certificate or digital badge in Shear vs Compression: The Missing Language of Spinal Load Management. The credential reflects demonstrated completion of the module’s learning outcomes under the assessment criteria declared at the opening of this page.
Module-Level Credential
Level 2 · Micro-Certificate Pathway
MMSx Micro-Certificate in Applied Biomechanics Decision Science
Cluster of Modules + Cumulative Assessment
Completion of this module, together with the required companion modules in the Applied Biomechanics Education Series and an associated cumulative assessment, may contribute toward an MMSx Micro-Certificate in Applied Biomechanics Decision Science. The micro-certificate is awarded only when the full module cluster and its integrating assessment are satisfactorily completed; individual module completions alone are necessary but not sufficient.
Grouped Pathway · Multi-Module
Level 3 · Advanced Certification Pathway
MMSx Certification in Mechanical Decision Science (Planned)
Identity-Verified · Multi-Module · Applied Evaluation
This module may also serve as one component within a future identity-verified MMSx certification pathway involving multi-module assessment, applied case analysis, proctored examination, and formal institutional evaluation. Certification at this level would reflect a higher-stakes, identity-verified standard rather than a module completion or digital badge.
Higher-Stakes · Formal Evaluation
Academic integrity statement. Credentials associated with MMSx academic modules should reflect demonstrated completion or assessed achievement and must not overstate the level of academic or professional recognition conferred by a single module alone. Module-level credentials are distinct from Micro-Certificates, which are distinct from full MMSx Certification pathways. All three tiers are governed by the MMSx Scientific Review Board and are reviewed against the standards declared in each module’s Version & Review block.
Faculty and institutional adoption. For institutional partners, module-level certificates and Micro-Certificate pathways may be adapted to local assessment, moderation, and LMS delivery structures. Universities and CPD providers retain the discretion to map this module against their own credit frameworks, learning outcomes, and quality-assurance processes. MMSx Authority Institute will supply module metadata, assessment specifications, and reviewer documentation on request.
Credential and pathway enquiries For learners, faculty, and institutional partners
```
🎓 Faculty Use Note
This module is optimised for flipped-classroom delivery. Recommended structure: learners complete Sections 1–5 and the 5 MCQs as pre-seminar work. The 60-minute seminar then focuses on the compression-vs-shear diagram (Figure 1) and the tolerance table at the whiteboard, the Case Translation Layer in small-group format, and the Case-Based Discussion Prompt as a structured debate. The Applied Interpretation Task serves as the summative assessment submitted one week after the seminar. The module also functions as a standalone clinical CPD reading for physiotherapists, ergonomists, strength coaches, and movement practitioners seeking to reorganise their spinal-load management logic.

References

Selected foundational and supporting references are listed below in numbered format. All external DOIs and registry entries are live-linked.

  1. National Institute for Occupational Safety and Health (NIOSH). Work Practices Guide for Manual Lifting. DHHS (NIOSH) Publication No. 81-122. Cincinnati, OH: NIOSH; 1981. (Source of the 3 400 N compression action-limit at L5–S1.)
  2. Yingling VR, McGill SM. Anterior shear of spinal motion segments: kinematics, kinetics, and resultant injuries observed in a porcine model. Spine. 1999;24(18):1882–1889. (Empirical shear-tolerance data used in tissue-tolerance table.)
  3. McGill SM. The biomechanics of low back injury: implications on current practice in industry and the clinic. J Biomech. 1997;30(5):465–475.
  4. McGill SM. Low Back Disorders: Evidence-Based Prevention and Rehabilitation. 3rd ed. Champaign, IL: Human Kinetics; 2015. (Reference tolerance values for compression and shear at the lumbar motion segment.)
  5. Gallagher S, Marras WS. Tolerance of the lumbar spine to shear: a review and recommended exposure limits. Clin Biomech. 2012;27(10):973–978.
  6. Cholewicki J, McGill SM. Mechanical stability of the in vivo lumbar spine: implications for injury and chronic low back pain. Clin Biomech. 1996;11(1):1–15.
  7. Mehta N. BPIT™ 5-Line Principle: Progressive Biomechanical Integration Training. MMSx Authority Institute. 2025. DOI 10.5281/zenodo.17594977.
  8. Mehta N. MMSx-SCAN™ v2.1: A Three-System Clinical Assessment Framework for Force Organisation. Open Science Framework. 2025. DOI 10.17605/OSF.IO/F87N2.
  9. MMSx Authority Institute. BPIT Pilot (ClinicalTrials.gov NCT07296640, n=23). Registered 2025.
  10. MMSx Authority Institute. BPIT Multi-Cohort (ClinicalTrials.gov NCT07256717, n=369). Registered 2025.
  11. Journal of Movement Mechanics & Biomechanics Science. ISSN 3070-3662 · DOI prefix 10.66078 · jmmbs.org.
Version & Review Status
Module ID
MMSx-EDU-02
Version
1.0
Original Publication
18 April 2026
Last Revision
18 April 2026
Review Status
Institutional Review ✓
Reviewer
MMSx Scientific Review Board
Next Scheduled Review
April 2027
Licence
CC BY 4.0
Corresponding Contact

Download This Module

Save as a formatted A4 PDF teaching handout. Print layout hides navigation and sidebar; assessment layer begins on a new page.